description	TPS2051DG4
Technical/Catalog Information	TPS2051DG4
Vendor	Texas Instruments
Category	Integrated Circuits (ICs)
Type	High Side Switch
Number of Outputs	1 - Single
Voltage - Input	2.7 ~ 5.5V
Package / Case	8-SOIC (3.9mm Width)
Packaging	Tube
Current Limit	900mA
Internal Switch(s)	Yes
Operating Temperature	-40掳C ~ 85掳C
Rds (On)	95 mOhm
Lead Free Status	Lead Free
RoHS Status	RoHS Compliant
Other Names	TPS2051DG4 TPS2051DG4

TPS2051DG4，there are the best TPS2051DG4 suppiers all over the world here.These are the list and detailed contact method of TPS2051DG4 suppliers all over the world as follows.You can buy or get informations of TPS2051DG4 through email , message or tel.

suppliers of TPS2051DG4 and PDF data of TPS2051DG4

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
TPS2051DG4	TI	SOP	08+		20000	A-RICH HK LECTRON CO.,LIMITED Contact:JING ZHOU Tel:86-755-33377586 Fax:86-755-33377578 Email: ARICH2@yahoo.cn
TPS2051DG4	TI	SOP		in stock	20155	WT Technology Int l.HK LIMITED Contact:Vivien Tel:86-755-82953360 Fax:86-755-82579304 Email: wt1@kwl-ic.com

TPS2051DG4 Datasheet

GND GND Filtl Filtl Filt2 Filt2 Filt3 Filt3 GND GND Filt4 Filt4 Filt5 Filt5 GND GND Filt6 Filt6 Filt7 Filt7 Filt8 FiltS GND GND

TPS2051DG4 Price

	FIGURE
Switched-Capacitor Building Block	12
Switched-Capacitor Equivalent Circuit	13
Circuit With Load Connected From VCC to VOUT	14
External-Clock System	15
Basic Regulation Configuration	16
Power-Dissipation-Limiting Resistor in Series With CIN	17
Motor-Speed Servo	18
Basic Voltage Inverter	19
Basic Voltage Inverter/Regulator	20
Negative-Voltage Doubler	21
Positive-Voltage Doubler	22
100-mA Regulating Negative Doubler	23
Dual-Output Voltage Doubler	24
5-V to +12-V Converter	25
Strain-Gage Bridge Signal Conditioner	26
3.5-V t0 5-V Regulator	27
Regulating 200-mA +12-V to -5-V Converter	28
Digitally Programmable Negative Supply	29
Positive Doubler With Regulation (5-V t0 8-V Converter)	30
Negative Doubler With Regulator	31

TPS2051DG4 on stock

Parameter	Test Conditions	Min Typ Max	Unit
DSP SECTION VIH Hi-LevelInput Voltage" 2 VIH Hi-Level CLKIN Voltage VIL Lo-LevelInput Voltage" 3 VOH Hi-Level Output Voltage" 4'5 VOL Lo-Level Output Voltage" 4'5 IIH Hi-LevelInputCurrent3 IIL Lo-Level Input Current3 IOZH Three-State Leakage Curren/ IOZL Three-State Leakage Current7 IDD Supply Current (Idle)9 IDD Supply Current (Dynamic)1 1 Ci Input Pin Capacitance3'6"2 CO Output Pin Capacitance6''''2"3	@ VDD = max @ VDD = max @ VDD = rriin @ VDD = min, IOH = -0.5 mA @ VDD = min, IOH = -100 LJA6 @ VDD = min,IOL = 2 mA @ VDD = max, VIN = VDD rriax @ VDD = max, VIN = 0 V @ VDD = max, VIN = VDD rriax8 @ VDD = max, VIN = 0 V8 @ VDD = 3.3 V tCK = 19 ns10 tCK = 25 ns10 tCK = 30 ns10 @ VDD = 3.3 V, TAMB = 250C tCK = 19 ns10 tCK = 25 ns10 tCK = 30 ns10 @ VIN = 2.5 V, fIN = 1.0 MHz, TAMB = 250C @ VIN = 2.5 V, fIN = 1.0 MHz, TAMB = 250C	2.0 0.8 2.4 VDD-0.3 0.4 10 10 10 10 14 12 10 54 43 37 8 8	V V V V V V I.iA IJA I.iA IJA mA mA mA mA mA mA pF pF

[7! DON'T CARE TRANSITIONING DATA NOTE :1. DO n (or b) = data-out from column n (or column b). 2. Burst length = 4 3. Three subsequent elements of data-out appear in the programmed order following DQ n. 4. Three subsequent elements of data-out appear in the programmed order following DQ b. 5. Shown with nominal tAC and tDOSO. 6. Example applies when READ commands are issued to different devices or nonconsecutive READs. 7. RDQS will start driving high one half-clock cycle prior to the first falling edge of RDQS.

Suppliers Datasheet
		Exact Matc