TP3076J-D(CERMIC) TP3076J-D(CERMIC) TP3076JDCERMIC，there are the best TP3076J-D(CERMIC) TP3076J-D(CERMIC) TP3076JDCERMIC suppiers all over the world here.These are the list and detailed contact method of TP3076J-D(CERMIC) TP3076J-D(CERMIC) TP3076JDCERMIC suppliers all over the world as follows.You can buy or get informations of TP3076J-D(CERMIC) TP3076J-D(CERMIC) TP3076JDCERMIC through email , message or tel.

suppliers of TP3076J-D(CERMIC) TP3076J-D(CERMIC) TP3076JDCERMIC and PDF data of TP3076J-D(CERMIC) TP3076J-D(CERMIC) TP3076JDCERMIC

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

TP3076J-D(CERMIC) TP3076J-D(CERMIC) TP3076JDCERMIC Datasheet

_NOTINCLUDING

-GATE CHARGE CUR

aENT

-C'

SLEEP MODE

TP3076J-D(CERMIC) TP3076J-D(CERMIC) TP3076JDCERMIC Price

Parameter	Symbol	Limits	Unit
]L	VCBO	-80	V
]L·-f'a	VOEO	-80	V
N	VEBO	-5	V
]L	lc	-700	mA
]L	PC	750	mW
	Tj	150
	Tstg	-55150

TP3076J-D(CERMIC) TP3076J-D(CERMIC) TP3076JDCERMIC on stock

2. Relative linearity is a measure of the error in step size between taps = VH(n+l)-[VH(n) + Ml] = +0.5 Ml, n = 1 .. 29 0nly 3. 1 Ml = Minimum Increment = RTOT/31. 4. Typical values are for TA = 250C and nominal supply voltage. 5. This parameter is periodically sampled and not 100% tested 6. Typical values are for TA = 250C and nominal supply voltage. 7. This parameter is not 100% tested. 8. When performing multiple write operations, Vcc must not decrease by more than 150mV from its initial value.

PARAMETER	TEST CONDITIONst		TAt	LM2904 LM2904Q	UNIT
PARAMETER	TEST CONDITIONst		TAt	MIN TYP~ MAX	UNIT
	vcc = 5 v to MAX,		250C	3 7
VIO Input offset voltage	VIC = VICR(min), VO = 1.4 V		Full range	10	mV
Average temperature coefficient of aVIO input offset voltage			Full range	7	¨VoC
			250C	2 50
IIO Input offset current	vo= 1.4 V		Full range	300	nA
Average temperature coefficient of al10 input offset current			Full range	10	pA/oC
			250C	-20 -250
IIB Input bias current	vo= 1.4 V		Full range	-500	nA
			250C	0 to VCC-1.5	V
VICR Common-mode input voltage range	vcc = 5 V to MAX		Full range	O tO VCC-2	V
	RL >2 kQ		250C		V
	RL >10 kQ		250C	VCC-1.5
VOH High-Ievel output voltage		RL=2 kQ	Full range	26
VOH High-Ievel output voltage	vcc= MAX	RL >10 kQ	Full range	23 24
VOL Low-Ievel output voltage	RL <10 kQ		Full range	5 20	mV
AVDLarge-signC	VCC =15 V, vo = 1 V t0 11 V		250C	25 100
AVDLarge-signC	RL=>2kQ		Full range	15	V/mV
CMRR Common-mode rejection ratio	vcc = 5 V to MAX, VIC = VICR(min)		250C	50 80	dB
voltage rejection ratio kSVR jAuypg'g/AV':. NVIO)	vcc = 5 v to MAX		250C	65 100	dB
VOIN02 Crosstalk attenuation	f =1 kHz t0 20 kHz		250C	120	dB
			250C	-20 -30
	VCC = 15 V, VID =1 V, VO = O		Full range	-10
IO Output current			250C	10 20	mA
	VCC=15vVID=-1VVO=15V		Full range	5	mA
	VID = -1 V VO = 200 mV		250C	30	yA
IOS Shorl-circuit output current	VCC at 5 V, GND at -5 V, VO = O		250C	±40 ±60	mA
	vo = 2.5 V, No load		Full range	0 7 1 2
ICC Supply current (two amplifiers)	vcc = MAX, VO = 0.5 V, No load		Full range	1 2	mA

Suppliers Datasheet
		Exact Matc