STV9937P，there are the best STV9937P suppiers all over the world here.These are the list and detailed contact method of STV9937P suppliers all over the world as follows.You can buy or get informations of STV9937P through email , message or tel.

suppliers of STV9937P and PDF data of STV9937P

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

STV9937P Datasheet

Symbol	Parameter	Test Conditions	Min	Typ.	Max	Unit
V(BR)DSS	Drain-source Breakdown Voltage	ID = 250 ccA VGS = 0 @ iOOoC	200			V
IDSS	Zero Gate Voltage Drain Current (VGS = 0)	VDS = Max Rating VDS = Max Rating Te = 125 0C			1 10	ccA ccA
IGSS	Gate-body Leakage Current (VDS = 0)	VGS=±30 V			±1 00	nA

STV9937P Price

PARAMETER	SYMBOL	TEST CONDITIONS		MIN	TYP	MAX	UNITS
Collector to Emitter Breakdown Voltage	BVCES	IC = 2500cA, VGE = OV		600			V
Emitter to Collector Breakdown Voltage	BVECS	IC = -10mA, VGE = OV		20			V
Collector to Emitter Leakage Current	ICES	VCE= BVCES	TC= 250C			100
Collector to Emitter Leakage Current	ICES	VCE= BVCES	TC= 1500C			6O	mA
Collector to Emitter Saturation Voltage	VCE(SAT)	IC = IC110,	TC= 250C		1.4	2.0	V
Collector to Emitter Saturation Voltage	VCE(SAT)	VGE = 15V	TC= 1500C		1.5	2 3	V
Gate to Emitter Threshold Voltage	VGE(TH)	IC = 2500cA, VCE = VGE		3.0	4.8	6O	V
Gate to Emitter Leakage Current	IGES	VGE= -OOV				+100	nA
Switching SOA	SSOA	Tj = 1500c	VCE= 480V	200			A
Switching SOA	SSOA	RG=3[ VGE = 15V L = 100ccH	VCE= 600V	100			A
Gate to Emitter Plateau Voltage	VGEP	IC = IC110, VCE = 0.5 BVCES			7.5		V
On-State Gate Charge	QG(ON)	IC = IC110,	VGE= 15V		250	330	nC
On-State Gate Charge	QG(ON)	VCE = 0.5 BVCES	VGE= 20V		335	435	nC
Current Turn-On Delay Time	dfONll	IGBT and Diode Both at Tj = 250C			47		ns
Current Rise Time	trI	ICE = IC110 VCE = 0.8 BVCES			35		ns
Current Turn-Off Delay Time	Ld(OFF)I	VGE = 15V RG=3[			170	200	ns
Current Fall Time	tfl	L = 100ccH			50	100	ns
Turn-On Energy	EON	Test Circuit (Figure 17)			1050	1200
Turn-Off Energy (Note l)	EOFF	Test Circuit (Figure 17)			800	1400

STV9937P on stock

Operation	R/W	BW1	BW2
READ	H	x	x
WRITE Byte "a"	L	L	H
WRITE Byte "b"	L	H	L
WRITE all bytes	L	L	L
WRITE Abort/NOP	L	H	H

RGB BLANK A logic "0" sets the registers to all "O's" (Ref Black) and drives the output to a level 53mV more negative than the Reference Blacklevel. This signalhas priority over the data inputs and is used to shut off the beam for the darkest display possible. Blanking is syn- chronous with strobe. SYNC ADJ This input should be left open to enable the 286 mV sync level feature of the Green Output. If the feature is not desired this input should be connected to ground. This is not a digital input.

Suppliers Datasheet
		Exact Matc