STP2223BGA-100-4611-05，there are the best STP2223BGA-100-4611-05 suppiers all over the world here.These are the list and detailed contact method of STP2223BGA-100-4611-05 suppliers all over the world as follows.You can buy or get informations of STP2223BGA-100-4611-05 through email , message or tel.

suppliers of STP2223BGA-100-4611-05 and PDF data of STP2223BGA-100-4611-05

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
STP2223BGA-100-4611-05	SUN		BGA		03	E-TOP International（HK）Holding.. Contact:Wendy Tel:00852-39706117 Fax:00852-27592926 Email: bella@ehk-ic.com
STP2223BGA-100-4611-05	SUN	BGA	3	new original parts	1	USA R&k HOLDINGS GROUP CO.LIMI.. Contact:liu Tel:0-852-66312187 Fax: Email: Jessica@ruik.us
STP2223BGA-100-4611-05	SUN		BGA		03	DHK INTERNATIONAL (HK) CO . ,.. Contact:Han Tel:+852 6081 9241 Fax:+852 6631 2078 Email: tina@dhk-int.com.hk
STP2223BGA-100-4611-05	SUN				1	ShenZhenHYCElectronicTechnolog.. Contact:Mr.lodgeliu/Catherine JI Tel:86-755-82956158 82958019 82958079 Fax:86-755-82956157 Email: catherine@hengyic.com
STP2223BGA-100-4611-05	SUN	BGA	04+	NEW	1	Dayue (HK) Trade Limited Contact:Zhao Tel:86-755-8301-3240 Fax:86-755-8304-1894 Email: Mike-hk@dayue-hk.com

STP2223BGA-100-4611-05 Datasheet

Pin No.	Name	Description
1	D2	Light if power on or pair
2	GND	Ground
3	ANT	RF input/output
4	Pl011	Programmable input/output
5	MIC P R	Microphone input positive (right side)
6	MIC N R	Microphone input negative (right side)
7	MIC P L	Microphone input positive (left side)
8	MIC N L	Microphone input negative (left side)

STP2223BGA-100-4611-05 Price

c s U o i x ) 2 1 Z J V L L A A O O S A ( V ) J ' 1 L N : l I W I n o A A O : J S f H s A l x v a d
STP2223BGA-100-4611-05 on stock

NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M,1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOTINCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTALIN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT.MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD

RECTANGULAR

WAVEFORM

180

3609

10mm 10mm

l l

{l-

[ rV

10mm

30mm×30mm

Suppliers Datasheet
		Exact Matc