STK4201 II T Datasheet| | | IDT72V275L IDT72V285L Cam"I & Ind'I o) tCLK = 10, 15, 20 ns | | | Symbol | Parameter | Min | Max | Unit | | ILl(2) | InputLeakageCurrent | 1 | 1 | UA | | IL0(3) | OutputLeakageCurrent | -10 | 10 | ¨A | | VOH | Output Loqic "1" Voltaqe, IOH = -2 mA | 2.4 | | V | | VOL | Output Logic "0" Voltage, IOL = 8 mA | | 0.4 | V | | lcci(4,5,6) | Active Power Supply Current | | 60 | mA | | lcc2(4,7) | StandbvCurrent | | 20 | mA | | | | | |
STK4201 II T Price| Collector-Emitter Voltage (G-E SHORT) | VCES | 1200 | Volts | | Gate-Emitter Voltage | VGES | +20 | Volts | | Collector Current | Jc | 15 | Amperes | | Peak Collector Current | ICM | 30* | Amperes | | Diode Forward Current | IF | 15 | Amperes | | Diode Forward Surge Current | IFM | 30* | Amperes | | Power Dissipation | Pd | 150 | Watts | | Max. Mounting Torque M5 Mounting Screws | | 17 | in-lb | | Module Weight (Typical) | | 150 | Grams | | V Isolation | VRMS | 2500 | Volts | | ' Pulse width and repetition rate should be such that device ji | unction temperature does not exceed the device rating. | | | | Static Electrical Characteristics, Tj | = 25 IC unless otherwise specified | | Characteristics | Symbol Test Conditions | Min. Typ. | Max. Units | | Collector-Cutoff Current | ICES VCE = VCES, VGE = OV | | 1.0 mA | | Gate Leakage Current | IGES VGE = VGES, VCE = OV | | 0 5 0A | | Gate-Emitter Threshold Voltage | VGE(th) lC =1. 5mA, VCE = 10V | 4.5 6.0 | 7.5 Volts | | | | |
STK4201 II T on stock| Cperating Voltage Range | | q q | 3.0 5.50 1.5 2.75 | V V | | VOUT Output Voltage | IOUT= 1mA | q | Vcc - 0.1Vcc - 0.01 Vcc - 0.2Vcc - 0.01 | V | | IOUT= 50mA | q | Vcc - 0.8Vcc - 0.4 | | | VOUTin Battery Back-Up Mode | IOUT= 250xA, Vcc< VBATT | q | VBATT - 0.1VBATT - 0.02 | V | | Supply Current (ExdudeIOUT) | IOUT " 50mA, Vcc = 3.6V | q | 0.2 0.6 0.2 1.0 | mA mA | | Supply Current in Battery Back-Up Mode | Vcc= OV, VBATT= 2V | q | 0.04 1 0.04 5 | | | Battery Standby Current (+= Discharge, - = Charge) | 3.6V > Vcc > VBATT + 0.2V | q | -0.02 0.02 - 0.10 0.10 | | | Battery ~tvitchover Threshold (Voc - VB/Xrr) | Power Up Power Down | | 70 50 | mV mV | | Battery Stvitchover Hysteresis | | | 20 | mV | | I?ATT ON QJtput Voltage (Note 4) | ISINK = 800ccA | q | 0.3 | | | I?ATT ON OJtput Short-Orcuit Current (Note 4) | BATT ON = VOUT, Sink Current EATT ON = OV, Source Current | q | 25 0.5 1 25 | mA | | | | | |
375mW = (VIN - 3.OV)300mA 375mW = VIN X 300mA - 900mW 1275mW = VIN X 300mA VIN(max) = 4.25V Therefo re, a 3.OV application at 300mA of output current can accept a maximum input voltage of 4.25V in the MSOP-8 package. For a full discussion of heat sinking and thermal effects on the voltage regulators, refer to the "Regulator Thermals" section of Micrels Designing with Low-Dropout Vo/tage Regu/ators Handbook.
|
