| Part Numbert | Mfg | Packt | D/C | Descriptiont | Qty | Company/Contact | |
| SKHI61 | Module | 73 |
|
 |
|||
| SKHI61 | NEC | 06+ | in stock | 20000 |
|
|
|
| SKHI61 | SEM | 49 |
|
|
|||
| SKHI61 | 08+ | 65 |
|
||||
| SKHI61 | SEMIKRON | 210 |
|
||||
| SKHI61 | NEC | 06+ | in stock | 20000 |
|
||
| SKHI61 | N/A | Module | 00+ | Inventory stock，low | 140 |
|
|
| SKHI61 | 73 |
|
|||||
| SKHI61 | SEMIKRON | 76 |
|
|
|||
| SKHI61 | 德国西门康 | 模块 | New original | 50 |
|
||
| SKHI61 | SEMIKRON | MODULE | N/A | new stock | 55 |
|
|
| SKHI61 | ?西门康 | 2008 | NEW IN STOCK | 158 |
|
||
| SKHI61 |
|
||||||
| SKHI61 | SEMIKRON | N/A | 04+ | N/A | 45 |
|
 
|
| SKHI61 | N/A | new and original in | 200 |
|
|||
| SKHI61 | 555 |
|
|||||
| SKHI61 | SEMIKRON | New&Original | 100 |
|
|||
| SKHI61 | SEMIKRON | 100 |
|
||||
| SKHI61 | SEMIKRON | STOCK | 500 |
|
|||
| SKHI61 | ORIGINALandNEW | 260 |
|
||||
| SKHI61 | SEMIKRON | 55 | MODULE |
|
SKHI61 Datasheet
SKHI61 Price The flowchart in the Programming section (Section 5, Figure 5-1) shows AMD's Flashrite algorithm. The Flashrite algorithm reduces programming time by using a 100 ps programming pulse and by giving each address only as many pulses to reliably program the data. After each pulse is applied to a given address, the data in that address is verified. If the data does not verify, additional pulses are given until it verifies or the maximum pulses allowed is reached. This process is repeated while se- quencing through each address of the device. This part of the algorithm is done at Vcc = 6.25 V to assure that each EPROM bit is programmed to a sufficiently high threshold voltage. After the final address is completed, the entire EPROM memory is verified at Vcc = VPP = 5.25 V SKHI61 on stock DESCRIPTION The SFH618N628A feature a high current transfer ratio, low coupling capacitance and high isolation voltage. These cou- pIers have a GaAs infrared emitting diode emitter, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a plastic DIP-4 package. The coupling devices are designed for signal transmission between two electrically separated circuits. The couplers are end-stackable with 2.54 mm spacing. Therefore multicouplers can easily be implemented and con- ventional multicouplers can be replaced. Creepage and clearance distances of >8 mm are achieved with option 6. This version complies with IEC 950 (DIN VDE 0805) for reinforced insulation up to an operation voltage of 400 VRMS or DC. Tone selection is achieved through six programming inputs and two control inputs (which allow either a logic "1 " or "0" to enable the device). A low distortion sinewave is generated at the TX Tone Output when the MX315A is enabled. The emitter follower output stage can source ImW directly into a 600fl load (OdBm). |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
