ADMap-9  > SK8GH062

suppliers of SK8GH062 and PDF data of SK8GH062

Part Numbert Mfg Packt D/C Descriptiont Qty Company/Contact  
SK8GH062 SEMIKRON  MODULE      42 
    SongYuan Electronics (HK) Co.,..
  • Contact:Vicky
  • Tel:86-755-83044194
  • Fax:86-755-83044175
  • Email: songyuan-chen@163.com
SK8GH062 SEMIKRON  N/A  04+  N/A  88 
    PENGHUIDA ELECTRONICS(HK) LIMI..
  • Contact:Xiao
  • Tel:86-755-82807577
  • Fax:86-755-82581450
  • Email: phdic9@gmail.com



SK8GH062 Datasheet

OV BIAS 1 V BIA 0 FA: ,250(
BIAS r o 1 - 1 -
50%( )FV 7 NI 3


SK8GH062 Price

RECTANGULAR
& WAVEFORM
- d
l j 09 r --d 3bU- iN11TTC,TT()N
t UVtIILIUU11UJ ANGLE
l t (ONE CELL)
|
L
| l L
l
|
d =30 L 600 900 1200 1800
|


SK8GH062 on stock
The MIC5156, MIC5157, and MIC5158 Super Low-Dropout (LDO) Regulator Controllers are single IC solutions for high- current low-dropout linear voltage regulation. Super LDOTM Regulators have the advantages of an external N-channel power MOSFET as the linear pass element. The MIC51 56/7/8 family features a dropout voltage as low as the RDS(ON) of the external power MOSFET multiplied by the output current. The output current can be as high as the largest MOSFETs can provide. The MIC5156/7/8 family operates from 3V t0 36V. The MIC5156 requires an externalgate drive supply to provide the higher voltage needed to drive the gate of the external MOSFET. The MIC5157 and MIC5158 each have an internal charge pump tripler to produce the gate drive voltage. The tripler is capable of providing enough voltage to drive a logic- level MOSFET t0 3.3V output from a 3.5V supply and is clamped t0 17.5V above the supply voltage. The tripler requires three external capacitors. The regulator output is constant-current limited when the controller detects 35mV across an optional external sense resistor. An active-low open-collector flag indicates a low voltage of 8% or more below nominal output. A shutdown (low) signal to the TTL-compatible enable control reduces controller supply current to less than l.q while forcing the output voltage to ground. The MIC5156-3.3 and MIC5156-5.0 controllers have inter- nally fixed output voltages. The MIC5156 [adjustable] output is configured using two external resistors. The MIC5157 is a fixed output controllerwhich is externally configu red to select

Mode CE OE PGM AO A1 A9 VPP vcc l/07-1/00
Read VIL VIL x x x x VCC VCC Data Out
Output Disable VIL VIH x x x x VCC VCC H-Z
Standby VIH x x x x x VCC VCC Hi-Z
Program VIL VIH VIL Pulse x x x 12.25V 5.25V Data In
Program Verify VIL VIL VIH x x x 12.25V 5.25V Data Out
Program Inhibit VIH x x x x x 12.25V 5.25V H-Z
Manufacturer Code(3) VIL VIL VIH VIL VIL VID VCC VCC 37H
Device Code(3) VIL VIL VIH VIH VIL VID VCC VCC 64H
Continuation Code(3) VIL VIL VIH VIL VIH VID VCC VCC 7FH