| SYMBOL | PARAMETER | CONDITIONS | MIN | TYP. | MAX | UNIT |
| IDC! | quiescent current (pin 2) | PD=0 rriW | | 280 | 320 | mA |
| PldB | load power | at l dB gain compression | 13 | 17 | | W |
| Gp | power gain | | 27 | 29 | 31 | dB |
| CGp freq | gain flatness over frequency range | | | 0.2 | 1 | dB |
| CGp pwr | gain flatness over power band | PL = 25 mW up t0 2.5 W | -0.8 | -0.2 | +0.2 | dB |
| GOB | out of band gain | small signal, PD = 0 dBm; f< 920 MHz, f > 960 MHz | | | GPimax + 1 note 1 | dB |
| VSWRin | input VSWR | | | 1.61 | 21 | |
| IMD | reverse intermodulation | fi = fe +100 kHz Pcarrier = 2.5 W; Pinterference = -40 dBc; | | -66 | -60 | dBc |
| H2 | second harmonic | | | -38 | -35 | dBc |
| H3 | third harmonic | | | -61 | -58 | dBc |
| | stability | VSWR " 3 : 1 through all phases; VS2 = 25 t0 28 V | all spurious outputs more than 60 dB below desired signal |
| | ruggedness | VSWR = 10 : 1 through all phases; PL = 5 W | no degradation in output power |
| EDGE (PL = 2.5 W average) |
| T1 | efficiency | | 12 | 15 | | % |
| SR200 | spectral regrowth; | 200 kHz | | -36 | -35 | dBc |
| SR400 | EDGE GSM signal | 400 kHz | | -65 | -63 | dBc |
| EVMrms | rms EDGE signal distortion | | | 0.4 | 1.2 | % |
| EVMM | peak EDGE signal distortion | | | 1.2 | 4 | % |
| Intermodulation distortion (PL = 2.5 W average) |
| d3 | third order intermodulation | carrier spacing = 200 kHz | | -45 | -40 | dBc |
| ds | fifth order intermodulation | | -52 | | dBc |
| d7 | seventh orderintermodulation | | -60 | | dBc |
| | | | | | |
| MCC Catalog Number | Device Marking | Maximum Recurrent Peak Reverse Voltage | Maximum RMS Voltage | Maximum DC Blocking Voltage |
| RB491D | 10T | 20V | 14V | 20V |
| RB490D | 10F | 40V | 28V | 40V |
| | | | |
SK2301RG3 on stock The tra nsmitter is configured for operation from either a single +5 V power supply or a single -5 V power sup- ply. For positive power supply operation, connect Vcc to the +5 V power supply and connect VEE to ground or circuit common. For operation from a -5 V power sup- ply, connect Vcc to ground and connect VEE to the -5 V power supply. Whichever option is chosen, the Vcc or VEE connection to the transmitter should be well filtered
Notes: /883B suffix denotes Mil-Std-883, Level B processing N - 8-lead plastic DIP D - 8 10ad ceramic DIP T - 8-lead metalcan T0-99 Contact a Raytheon sales office or representative for ordering information on special package/temperature range combinations.
