description	RES 24.9K OHM 1/16W .5% 0603 SMD
Technical/Catalog Information	RR0816P-2492-D-39C
Vendor	Susumu Co Ltd (VA)
Category	Resistors
RoHS Status	RoHS Compliant
Other Names	RR0816P 2492 D 39C RR0816P2492D39C RR08P24 9KDDKR ND RR08P249KDDKRND RR08P24.9KDDKR
Lead Free Status	Lead Free
Packaging	Digi-Reel庐
Tolerance	卤0.5%
Temperature Coefficient	卤25ppm/掳C
Resistance In Ohms	24.9K
Voltage - Working	39.607V
Power (Watts)	0.063W, 1/16W
Lead Style	Surface Mount (SMD - SMT)
Case	0603 (1608 metric)
Composition	Thin Film

RR0816P-2492-D-39C，there are the best RR0816P-2492-D-39C suppiers all over the world here.These are the list and detailed contact method of RR0816P-2492-D-39C suppliers all over the world as follows.You can buy or get informations of RR0816P-2492-D-39C through email , message or tel.

suppliers of RR0816P-2492-D-39C and PDF data of RR0816P-2492-D-39C

Part Numbert

Mfg

Packt

D/C

Descriptiont

Qty

Company/Contact

RR0816P-2492-D-39C Datasheet

SYMBOL	PARAMETER	CONDITIONS	TYP	MAX	UNIT
VCESM VCBO VCEO lc ICM Ptot VCEsat hFE tf,	Collector-emitter voltage peak value Collector-Base voltage (open emitter) Collector-emitter voltage (open base) Collector current (DC) Collector current peak value Total power dissipation Collector-emitter saturation voltage Fall time (lnductive)	VBE=OV Tlead " 25 aC lc = 0.75 A;IB = 150mA lc = 0.75 A;VCE = 5 V lc = 1.0 A;IBON = 200mA	0.24 14 50	700 700 400 1.0 2.0 2 1.0 20 70	V V V A A W V ns

RR0816P-2492-D-39C Price

Switch current is continuously monitored by C2, which The switch used in the LT1074 is a Darlington NPN (single resetsthe R/S latch to turn the switch off if an overcurrent I for LT1076) driven by a saturated PNP. Special ;uitry is used to drive the PNP on and off ve ry 1 from the saturation state. This particular has no "isolation tubs" connected to condition occurs. The time required for dete'tion and thereforeswingt040Vbelow switch turn off is approximately 600ns. So minimum nted circui switch "on" time in current limit is 600ns. Under dead shorted output conditions, switch duty cycle may have to be as low as 2% to maintain control of output current. This the swi would require switch on time of 200ns at lOOkHz switch- ground. ing frequency, so frequency is reduced at ve ry low output
RR0816P-2492-D-39C on stock

Pin	Function	Description	Device Schematic
1	N/C	No Connection.
2	N/C	No Connection.
3	RF IN	RF input pin. This pin requires the use of an external DC blocking capacitor chosen for the frequency of operation.
4	Vcc	Supply connection. This pin should be bypassed with a suitable capacitor(s).	7
5	GND	Connected to ground. For best performance use via holes as close to ground leads as possible.	l	7
6	RF OUT VCC	RF output and DC supply. This pin requires the use of an external DC blocking capacitor chosen for the frequency of operation.

Item	Symbol	Conditions	ZD	Di	Unit
Movement Start Voltage	VBR	IR= ImA	MIN 74 TYP 82 MAX 90		V
Restriction Voltage	VCL	IPP= 1.7A	MAX 118		V
Leak Current	IR	VR= VRVI	MAX 5	MAX 5	uA
Reverse Recovery Time	trr	IF/IR=O.1A/0.3A		MAX 500	ns
Thermal Resistance	OjL	Junction to lead	MAX 17	MAX 17	/W

Suppliers Datasheet
		Exact Matc