RPE132901CH220J50OCT，there are the best RPE132901CH220J50OCT suppiers all over the world here.These are the list and detailed contact method of RPE132901CH220J50OCT suppliers all over the world as follows.You can buy or get informations of RPE132901CH220J50OCT through email , message or tel.

suppliers of RPE132901CH220J50OCT and PDF data of RPE132901CH220J50OCT

Part Numbert	Mfg	Packt	D/C	Descriptiont	Qty	Company/Contact
RPE132901CH220J50OCT	murata	07+	DIP		15000	bandsholdings Contact:Mr.chenjack Tel:0086-755-61390007 Fax:0086-755-61390086 Email: jack@luyeic.com

RPE132901CH220J50OCT Datasheet

Parameter	Symbol	Min	Max	Units
Input capacitance [AO ~ A12]	CIN1		5	pF
Input capacitance [RAS, AS, W, OE]	CIN2		7	pF
Output capacitance [DQO - DQ3]	CDO		7	pF

RPE132901CH220J50OCT Price

Item		Symbol	Condition	mln	typ	max	Unit
Collector cutoff	2SB954	Ic EO	VCE= -30 V, IB=O.			-300	A
current	2SB954A	Ic EO	VCE= -60 V, IB=O			- 300	A
Collector cutoff	2SB954		VCE= -60 V, VBE=O			-200
current	2SB954A	ICES	VCE=--80 V, VBE=O			-200	A
Emitter cutoff current		IEBO	VEB= -5 V, lc =0			-1	mA
Collector-	2SB954			- 60
emitter voltage	2SB954A	VCEO	Ic= -30 mA, IB=O	- 80			V
		hFEl*	VCF.= -4 V, Ic= -0.2 A	40		450
DC current gain		hEF2	VCF.= -4 V, lc= -1 A	15
Collector-emitter saturation voltage		VCEtsar,	IC=-1A.IB=-0.125A			-1	V
Base-emitter saturation voltage		VBE	VCE=-4V.Ic=-lA			-1.3	V
Transition frequency		fT	. VCE= -5V, IC= -0.2A, f=lO'VIHz		30		MHz
Turn-on time		ton			O5		S
Storage time		tstg	Ic = -1A, IBl = - O.lA. lB2 = O.lA, . vcc= - 50V		1.2		S
CoUector current fall time		tt	Ic = -1A, IBl = - O.lA. lB2 = O.lA, . vcc= - 50V		0.3		S

RPE132901CH220J50OCT on stock

Type	Ordering code
BF 457	Q62702-F315
BF 458	Q62702-F316
BF 459	Q62702-F317
Mica washer	Q62902-B62
Spring washer	Q62902-B63
A3 DIN 137	Q62902-B63

1. Each ECL 10,000 series device has been designed to meet the DC specifications shown in the tast table. after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Voltage levels will shift approximately 4 mV with an air flow of 200 linear fpm. Outputs are terminated through a 90fl to gnl and a 845fl to VEE. 2. For AC tests. all input and output cables to the scope are equal lengths of 50-ohm coaxial cable. Wire lengths should be <1/4 inch from TPin to input pin and TPout to output pin. A 50-ohm termination lo ground is located in each scope input. Unused outputs are con- nected to a 90-ohm resistor to ground and a 845fl to VEE. 3 bst procedures are shown for only one input or set of input conditions. Other inputs are tested in the sama manner.

Suppliers Datasheet
		Exact Matc