QL3025-OPQ208I Datasheet| Characteristic | Symbol | Test Condition | Min | Typ | Max | Unit | | Forward voltage | VF | IF= 100mA | | 1.8 | 2.2 | V | | Reverse current | IR | VR= 4V | | | 60 | pA | | Radiant power | PO | IF= 50mA | 14 | 18 | | mW | | Radiant intensity | IE | IF= 50mA | | 100 | | mW /sr | | Rise time, fall time | trtf | IFP = 100mA, Pw = 100ns | | 30 | | ns | | Cut-off frequency (Note 2) | fc | IF = 50mADC + 5mAp-p | 10 | 15 | | MHz | | Capacitance | CT | VR = O,f = 1MHz | | 110 | | pF | | Peak emission wavelength | ^P | IF= 50mA | 830 | 870 | 900 | nm | | Spectral line half width | ^ | IF= 50mA | | 50 | | nm | | Half value angle | e 2 | IF= 50mA | | +5 | | | | | | | | | |
QL3025-OPQ208I Price| Collector-emitter breakdown voltage /C = 1 mA, /B = 0 | V(BR)CEO | 1 5 | | | V | | Collector-emitter cutoff current VCE = 25 V, VBE = 0 | /CES | | | 200 | UA | | Collector-base cutoff current VCB = 10 V, /E = 0 | /CBO | | | 1 00 | nA | | Emitter-base cutoff current VEB = 1 V, /C = 0 | /EBO | | | 2 | UA | | DC current gain /C = 200 mA, VCE = 5 V | hFE | 50 | 1 20 | 250 | | | | | | | |
QL3025-OPQ208I on stock| Parameter | Minimum | Typical | Maximum | Unit | Conditions | | DC Characteristics | | Operating Voltage VDD | 3.0 | | 5.50 | V | Host side | | Operating Current IDD | | | 10 | mA | Host side | | Operating Voltage VDDL | 2.8 | | 3.2 | V | Line side, derived from tip and ring | | Operating Current IDDL | | 7 | 8 | mA | Line side, drawn from tip and ring while off-hook | | On-hook Characteristics | | Metallic DC Resistance | 10 | | | M l | Tip to ring, 100 Vdc applied | | Longitudinal DC Resistance | 10 | | | Ml | 150 Vdc applied from tip and ring to Earth ground | | Ring Signal Detect Level | 5 | | | VRMS | 68 Hz ring signal applied to tip and ring | | Ring Signal Detect Level | 28 | | | VRMS | 15 Hz ring signal applied across tip and ring | | Snoop Circuit Frequency Response | 166 | | >4000 | Hz | -3 dB corner frequency @ 166 Hz, in Clare applica- tion circuit | | Snoop Circuit CMRR | | -40 | | dB | 120 VRMS 60 Hz common-mode signal across tip and ring | | Ringer Equivalence | | O1B | | REN | | | Longitudinal Balance | 60 | | | dB | Per FCC part 68.3 | | Oft-Hook Characteristics | | AC Impedance | | 600 | | l | Tip to ring, using resistive termination application circuit | | Longitudinal Balance | 40 | | | dB | Per FCC part 68.3 | | Return Loss | | 26 | | dB | Int0 600 I at 1800 Hz | | Transmit and Receive Characteristics | | Frequency Response | 30 | | 4000 | Hz | -3 dB corner frequency 30 Hz | | Trans-Hybrid Loss | | 36 | | dB | Int0 600 I at 1800 Hz, with C18 in the resistive ter- mination application circuit | | | | | | |
| Symbol | Parameter | Test Conditions(l) | Max. | Unit | | lccc! | Quiescent PowerSupply Current | Vcc = Max., VIN = GND or Vcc, f = 0 | 12 | uA | | lcc | Power Supply Current per Controllnput HIGH (2) | Vcc = Max., VIN = 3V or Vcc, f = 0 | 50 | uA | | ICCD | Dynamic Power Supply Current per MHz(3) | Vcc = Max., A and B pins open Controllnputs Toggling at 50% Duty Cycle | 0.15 | mA/M Hz | | | | | |
|
