| Part Numbert | Mfg | Packt | D/C | Descriptiont | Qty | Company/Contact | |
| C1883ACT | 2500 |
|
|||||
| C1883ACT | NEC | 55 |
|
||||
| C1883ACT | NEC | DIP30 | NA | 208 |
|
||
| C1883ACT | NEC | 175 |
|
||||
| C1883ACT | NEC | 拆机 | 2 |
|
|||
| C1883ACT | new and or | 08+ | 4500 |
|
|||
| C1883ACT | NEC | DIP | in stock | 169 |
|
![]()
|
|
| C1883ACT | NEC | 98+ | ★★★★★parts in room,n | 1087 |
|
||
| C1883ACT | NEC | DIP | 96 | 395 |
|
||
| C1883ACT | NEC | 09+ | STOCK | 157 |
|
||
| C1883ACT | 1261 |
|
|||||
| C1883ACT | NEC | 98+ | 1087 |
|
![]()
|
||
| C1883ACT | AD | N/A | 04+ | sales@bmc-ic.com | 100 |
|
|
| C1883ACT | NEC | 08+ | 39200 |
|
![]() |
||
| C1883ACT | NEC | DIP | delivered in 2-7 da | 4300 |
|
||
| C1883ACT | 2500 |
|
|||||
| C1883ACT | 2530 |
|
|||||
| C1883ACT | NEC | DIP | STRC Verified | 264 |
|
||
| C1883ACT | NEC | . | . | . |
|
||
| C1883ACT | NEC | DIP | STRC Verified | 264 |
|
![]()
|
|
| C1883ACT | 6000 |
|
|||||
| C1883ACT | DIP | NEC | 96+ | 395 |
|
![]() |
|
| C1883ACT | NEC | 98 | New&Original | 175 |
|
||
| C1883ACT | DIP | 05+ |
|
||||
| C1883ACT | NEC | DIP | 07+ | 395 |
|
||
| C1883ACT | NEC | DIP | 07+ | STOCK | 495 |
|
|
| C1883ACT | NEC | DIP30 | 2007+ | E-mailtome. | 9985 |
|
|
| C1883ACT | N/A | NEC | 04+ | 3000 |
|
||
| C1883ACT | DIP | 96+ | NEC | 395 |
|
||
| C1883ACT | NEC | 98 | 175 |
|
|||
| C1883ACT | NEC | 400 |
|
||||
| C1883ACT | NEC | DIP | 96+ | http://www.silicon-i | 395 |
|
|
| C1883ACT | 05+ | 76 |
|
C1883ACT Datasheet
C1883ACT Price Load Regulation OoC<TA<+700C - 0.006 0.010 0.007 0.012 %/mA {IL=Ot08mA)(Note4) -550CSTA<+1250C - 0.007 0.012 0.009 0.015 C1883ACT on stock Oscillation: To test RF characteristic this module is put on a fixture with 2 bias decoupling capacitors each on Gate and Drain, a 4.700pF chip capacitor, located close to the module, and a 22pF (or more) electrolytic capacitor. When an amplifier circuit around this module shows oscillation following may be checked: a) Do the bias decoupling capacitors have a low inductance pass to the case of the module ? b) Is the load impedance ZL=50Q ? c) Is the source impedance ZG=50Q ?
As a guideline to help in the selection of the LT1229/ LT1230 the following table describes the maximum sup- ply voltage that can be used with each part in cable driving applications. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||